Nyhet
TANK TÄTNING "TANK CURE"
459 SEK/st.
Poly service 450 gram epoxy 2 komponent tank tätning. För plåt tankar upp till ca. 20 liter. Viktigt att man rengör tanken noggrant före användning, använd tankrengöring U6/75-2900. Tanktätningen ska torka minst 7 dagar före man fyller på bensin eller olja.
Beskrivning
Art.nr: U6/75-2903
Application of the tank sealant
In order to guarantee a good result you always have to do some preparation on your tank Before you apply the sealant the tank should be absolutely dry, free of grease and almost free of rust. It is strongly recommended to use our TANK CURE Cleaner and TANK CURE Rust Remover according to our user guidelines to guarantee a good result. These products are extensively tested in combination with our Tank Sealant.•It takes 7 days before you can use the tank as the Tank Cure Epoxy Coating has to dry out completely.
Note: Not for use with aluminum, plastic, fiberglass or any other composite material tanks due to chemical reaction.
"TANK CURE" Tank Cleaner
This is a strong claening fluid to degrease your tank. We advise to always use this product because it will guarantee a good adhesion of the sealant to the surface of the patrol tank. Especially if you apply the sealant in a tank for a two stroke engine it is nessesary to use the tank cleaner first.
"TANK CURE" Rust Remover
Tanks with a rusted interior can be treated very succesfully with this product. We advise to use the Rust Remover if the inside of your tank is severely rusted.
"TANK CURE" Epoxy Remover
This product will remove all old layers of pait and/or sealants. Only use this product if you would like to apply a new sealant or if you plan to weld on your tank. You only need this product if you like to remove old layers of sealant or paint or if welding is needed on a tank that has sealant inside.
For a motorcycle tank you will need 1/2 a litre of Tank Cleaner and 1/2 a litre of Rust Remover.
In order to guarantee a good result you always have to do some preparation on your tank Before you apply the sealant the tank should be absolutely dry, free of grease and almost free of rust. It is strongly recommended to use our TANK CURE Cleaner and TANK CURE Rust Remover according to our user guidelines to guarantee a good result. These products are extensively tested in combination with our Tank Sealant.•It takes 7 days before you can use the tank as the Tank Cure Epoxy Coating has to dry out completely.
Note: Not for use with aluminum, plastic, fiberglass or any other composite material tanks due to chemical reaction.
| "TANK CURE" tank sealant is based on a 2 component epoxy resin. After adding the two components together stir them thoroughly for a couple of minutes, empty the can in your petrol tank and seal the filler opening properly. Now slowly turn the tank in all directions. Keep turning for about 15 to 20 minutes. The sealant should touch all surfaces several times to form a good layer. Now open the filler cap and put the tank upside down to drain as much sealant as possible. |
"TANK CURE" Tank Cleaner
This is a strong claening fluid to degrease your tank. We advise to always use this product because it will guarantee a good adhesion of the sealant to the surface of the patrol tank. Especially if you apply the sealant in a tank for a two stroke engine it is nessesary to use the tank cleaner first.
"TANK CURE" Rust Remover
Tanks with a rusted interior can be treated very succesfully with this product. We advise to use the Rust Remover if the inside of your tank is severely rusted.
"TANK CURE" Epoxy Remover
This product will remove all old layers of pait and/or sealants. Only use this product if you would like to apply a new sealant or if you plan to weld on your tank. You only need this product if you like to remove old layers of sealant or paint or if welding is needed on a tank that has sealant inside.
For a motorcycle tank you will need 1/2 a litre of Tank Cleaner and 1/2 a litre of Rust Remover.